Sling attachment guidance for the IWI Tavor X95. Check your exact configuration and both connectors before choosing the McLean Dynamic Retention Sling (DRS). Factory attachment points do not by themselves confirm a direct fit.
Front attachment
Documented X95 QD attachment points — factory attachment point.
IWI’s X95 manual includes quick-detach sling swivels in its accessory guidance. Its sling article identifies the X95’s attachment options. Use the actual QD cup and a compatible swivel; do not assume a bare accessory rail is itself a sling socket.
Factory attachment point: a QD cup needs a matching swivel; a socket provision may also need a separate cup. Confirm what is installed and what the hardware includes.
Rear attachment
Rear X95 sling attachment — factory attachment point.
IWI documents attachment choices on both sides of the X95. Confirm the rear cup or documented attachment you intend to use on the exact rifle. A QD swivel must seat in the socket, while a webbing route requires a suitable loop; these are different connections.
Factory attachment point: confirm the connector fits and closes fully on the exact attachment. The existence of a loop does not establish McLean connector clearance.
Why this sling on the IWI Tavor X95
Bullpup stocks place the action and magazine toward the rear. Check the strap route around that layout and use the documented attachment points to support comfortable, controlled carry.
The McLean design is a two-point sling with a patented retention system: it cinches tight to hold the bullpup against your body hands-free, then releases into a ready position in one pull. It ships in one size and adjusts, so there is no length to choose.
Fitting it
- Clear the bullpup. Unload and clear it following the firearm manufacturer’s instructions before fitting any accessories.
- Front: confirm a compatible connector and follow the sling and attachment manufacturer instructions.
- Rear: confirm the matching connector for your stock or rear attachment; do not assume a slot, stud and QD cup are interchangeable.
- Adjust wearing your kit. A setting dialled in without a vest comes up short once it is on.
- Check the transition. It should shoulder without pulling tight across your chest.
Choosing hardware for your configuration
This page is for the X95. The related Tavor SAR and TS12 shotgun have their own configurations, so matching the Tavor brand name is not enough to establish the correct fittings. The image depicts the .300 BLK X95 variant.
Before choosing McLean hardware, compare the connector requirements at both ends and check the accessories supplied with your rifle. The IWI references identify factory options; they do not certify every aftermarket stock accessory or replacement component.
Questions
Does the McLean Dynamic Retention Sling (DRS) fit the IWI Tavor X95?
Compatibility depends on the exact configuration and connectors. Confirm both attachment points and the connector fit before ordering. A factory attachment point does not by itself confirm a direct fit for the McLean sling.
Do I need a snap hook for the front of my IWI Tavor X95?
The McLean sling already carries a front hook. Choose a compatible attachment loop or swivel for that hook, and confirm its clearance and closure on your exact setup before buying additional hardware.
What do I need to buy for the IWI Tavor X95?
Front: Factory attachment point: a QD cup needs a matching swivel; a socket provision may also need a separate cup. Confirm what is installed and what the hardware includes. Rear: Factory attachment point: confirm the connector fits and closes fully on the exact attachment. The existence of a loop does not establish McLean connector clearance.
What length sling do I need for the IWI Tavor X95?
There is no length to choose. The sling ships in one size and adjusts, so the same sling covers carry and cinched retention. Set it wearing the kit you actually carry in — a setting dialled in without a vest or heavy coat comes up short once it is on.
Manufacturer and attachment references
Other firearms we have fitment for
Firearm photos: IWI Tavor TS12 — IWI US, Manufacturer image used with permission (Background removed; proportionally resized and centered on a transparent 1536 × 768 canvas.); FN PS90 — Metroplex at English Wikipedia, CC BY-SA 3.0 (Background removed with segmentation and reviewed manual mask corrections; subject cropped, proportionally resized and centered on a transparent 1536 × 768 canvas.); Steyr AUG — Alexdelarge15, CC BY-SA 4.0 (Background removed with segmentation and reviewed manual mask corrections; subject cropped, proportionally resized and centered on a transparent 1536 × 768 canvas.); Springfield Armory Hellion — Springfield Armory, Manufacturer product image (Background removed with segmentation and reviewed manual mask corrections; subject cropped, proportionally resized and centered on a transparent 1536 × 768 canvas.).
