Sling attachment guidance for the KelTec RDB. Check your exact configuration and both connectors before choosing the McLean Dynamic Retention Sling (DRS). Factory attachment points do not by themselves confirm a direct fit.
Front attachment
Hook-style sling attachment point at the front of the handguard — factory attachment point.
KelTec's RDB manual states that the rifle has numerous ambidextrous sling attachment points compatible with a hook style swivel, and its drawing marks one at the front of the handguard. These are openings for a hook, not push-button QD sockets.
Factory attachment point: confirm the connector fits and closes fully on the exact attachment. The existence of a loop does not establish McLean connector clearance.
Rear attachment
Hook-style sling attachment points on the receiver and at the top of the stock — factory attachment point.
The same manual drawing marks further attachment points on the receiver and one at the top rear of the stock. KelTec says they are meant for the included 1¼ in nylon sling and most hook style aftermarket slings. A QD swivel will not seat in them without an adapter.
Factory attachment point: confirm the connector fits and closes fully on the exact attachment. The existence of a loop does not establish McLean connector clearance.
Add it to your cart
Pick a colour and add the sling. You can review everything in your cart.
Why this sling on the KelTec RDB
Bullpup stocks place the action and magazine toward the rear. Check the strap route around that layout and use the documented attachment points to support comfortable, controlled carry.
The McLean design is a two-point sling with a patented retention system: it cinches tight to hold the bullpup against your body hands-free, then releases into a ready position in one pull. It ships in one size and adjusts, so there is no length to choose.
Fitting it
- Clear the bullpup. Unload and clear it following the firearm manufacturer’s instructions before fitting any accessories.
- Front: confirm a compatible connector and follow the sling and attachment manufacturer instructions.
- Rear: confirm the matching connector for your stock or rear attachment; do not assume a slot, stud and QD cup are interchangeable.
- Adjust wearing your kit. A setting dialled in without a vest comes up short once it is on.
- Check the transition. It should shoulder without pulling tight across your chest.
Choosing hardware for your configuration
The cited manual covers the original RDB-17 and RDB-20. KelTec publishes separate manuals for the RDB Survival and the RDB-C Hunter, which have different forends and should be checked on their own.
The RDB's points suit hook-style connectors. The manual also notes two Picatinny rails, above the barrel and on the handguard, which accept rail mounts if a different connection is wanted. Confirm which connectors come with the sling.
Questions
Does the McLean Dynamic Retention Sling (DRS) fit the KelTec RDB?
Compatibility depends on the exact configuration and connectors. Confirm both attachment points and the connector fit before ordering. A factory attachment point does not by itself confirm a direct fit for the McLean sling.
Do I need a snap hook for the front of my KelTec RDB?
The McLean sling already carries a front hook. Choose a compatible attachment loop or swivel for that hook, and confirm its clearance and closure on your exact setup before buying additional hardware.
What do I need to buy for the KelTec RDB?
Front: Factory attachment point: confirm the connector fits and closes fully on the exact attachment. The existence of a loop does not establish McLean connector clearance. Rear: Factory attachment point: confirm the connector fits and closes fully on the exact attachment. The existence of a loop does not establish McLean connector clearance.
What length sling do I need for the KelTec RDB?
There is no length to choose. The sling ships in one size and adjusts, so the same sling covers carry and cinched retention. Set it wearing the kit you actually carry in — a setting dialled in without a vest or heavy coat comes up short once it is on.
Manufacturer and attachment references
Other firearms we have fitment for
Firearm photos: KelTec SUB2000 — KelTec, Manufacturer image used with permission (Background removed; proportionally resized and centered on a transparent 1536 × 768 canvas.); KelTec KS7 — KelTec, Manufacturer image used with permission (Background removed; proportionally resized and centered on a transparent 1536 × 768 canvas.); KelTec RDB — KelTec, Manufacturer image used with permission (Background removed; proportionally resized and centered on a transparent 1536 × 768 canvas.); FN PS90 — Metroplex at English Wikipedia, CC BY-SA 3.0 (Background removed with segmentation and reviewed manual mask corrections; subject cropped, proportionally resized and centered on a transparent 1536 × 768 canvas.); Steyr AUG — Alexdelarge15, CC BY-SA 4.0 (Background removed with segmentation and reviewed manual mask corrections; subject cropped, proportionally resized and centered on a transparent 1536 × 768 canvas.); Springfield Armory Hellion — Springfield Armory, Manufacturer product image (Background removed with segmentation and reviewed manual mask corrections; subject cropped, proportionally resized and centered on a transparent 1536 × 768 canvas.); IWI Tavor X95 — IWI US, Manufacturer image used with permission (Background removed; proportionally resized and centered on a transparent 1536 × 768 canvas.).
